How to Make Garden Shed Doors

How to Make Garden Shed Doors

Like most homeowners, I have an endless list of repairs and projects that need to be done. Making a new set of garden shed doors has been on mine for several years. I am not sure when this tool shed was built, but I would guess 30-35 years ago. It’s a great storage space and is well constructed, but the doors have been falling apart for a long time.

I have made temporary repairs on them three times, which now seems like wasted time and effort. In each instance, I had to remove the doors, cut away rotted boards, add new fasteners, sand and repaint. The process took a weekend. I could have easily made new doors in about the same amount of time!

Garden shed doors

Yes, you can make garden shed doors for under $100!

If you stick with simple construction materials and methods, it’s surprisingly affordable. Here’s a breakdown of my costs:

  • 2×6 x 8′ boards (6):  $27.42
  • 1/4″ sheet of plywood: $27.72
  • Quart of paint: $21.95
  • Pocket screws $5.47

Total: $82.56

The lesson for me is to evaluate home repair jobs carefully to determine if my time is better spent fixing or building.

Cutting the boards

I used three, eight foot long (244cm), 2×6 boards for each door. These are actually 1.5″ x 5.5″ or 38mm x 140mm. I bought construction grade Douglas fir boards. Like 2x4s, the long edges are rounded over a little. In order to get a nice tight fit when assembling, I like to cut the edges off of each board to square them up.

Image1

I cut the four long side pieces to size using my miter saw. I measured the first one, then used it do line up and measure the rest. This is a much better method for making repeated cuts, rather than measuring each one with a tape measure.Image2

Image3

To cut the eight short pieces (the horizontal frame boards) all the same length, I set up an extension fence on my saw and clamped a stop block to it.

Image4

Then I butted the boards up to it so they all cut identically.

Image5

Assembly

Using my Kreg Jig, I drilled two pocket holes in ends of all the short pieces.

Image6

I began the assembly by screwing the top and bottom pieces into place.

Image7

To position the two middle boards equally apart from each other, I cut two scrap boards to use as spacers. This is much more accurate than trying to measure and mark where each board should be.

Image8

Image9

Routing profiles

I used my router to cut a rabbet (ledge) along the inside edge of each of the frames. For this, I used a rabbet bit. 

Image11

Image10

On the front side of the doors, I routed out a decorative Roman ogee profile.

Image12

Image13

The panels are 1/4″ (6mm) plywood. I cut these to size, and then glued and tacked them into the back side of the doors, resting on the rabbets.

Image14

Image15

Installation

I lined the doors up to where the old ones were, marked the hinge positions, and screwed them in place. This can be a time-consuming process. Dealing with hinges is one of my least favorite things!

Image16

 

Image17

Once everything was working properly, I removed the doors and painted them with a quality exterior latex paint. It’s important that all surfaces get painted in order to protect the wood from the weather.

Image18

Making the latch

On the inside of the right hand door, I installed a sliding bolt for keeping it closed. When extended, the bolt catches behind the door frame.

Image19

To make the latch, I found an old steel L-bracket and bent it into a squarish U-shape. I screwed this onto the right hand door.

Image20

On left door I attached a board with a screw and a lock nut so it can swivel freely.

Image21

Image22

SIMILAR ARTICLES

K-Cup Coffee Pod Dispenservideo

6 6702
Dresser Drawer Storage Systemvideo

2 3669

9 COMMENTS

  1. Steve, sure hope you don’t expect to keep any thieves out of your Shed; seeing that your door hinge pins are on the outside. But nice doors though. Always watch your vids, keep up the ….. GRIPPPER!!

  2. I love your project because they fit just about any home owner and things we run into regularly and I love all the helpful tips you not only give but demonstrate and I love watching you work too.

  3. Suggestions for putting this together without pocket holes?
    I think all your projects are great and lots of fun to watch and a great tool to learn from.
    Thanks!

  4. Love your videos and your “oh well” or “good enough” attitude when it comes to slight imperfections and also the fact you show your mess ups. Keep up the great work!

    You may want to add a washer between the latch and the door to stop the latch from scrapping your paint on the door.

  5. Steve you started me out making things out of old pallets. I have now made a boat planter windmills garden planters hall way stand garden benches chairs table and lots more I watch you every week and each day I am looking at your projects. I wish I had a big workshop or garage as I am only working out of a very cramped shed. Just to say I am in the UK.

  6. Steve,
    These doors are exactly what I’m looking to build. It was very timely that I saw this. I do have one question. Is there an issue using Green Fir 2×6 lumber instead of kiln dried boards? I’m concerned of the doors warping or changing shape after drying.

    You have been an inspiration. Thank you!

Leave a Reply